SW1801P Vibration Switch Module 4 Pin

40,00 EGP

موديول مفتاح اهتزاز SW1801P بيغلف مفتاح SW-520D في بورد جاهز مع مؤشرات LED للطاقة والحالة. | The SW1801P Vibration Switch Module wraps the SW-520D tilt switch in a ready-to-use board with onboard power and status LEDs.

Description

SW1801P Vibration Switch Module (4 Pin)

The SW1801P Vibration Switch Module takes the bare SW-520D mechanical tilt switch and mounts it on a breakout board with a comparator circuit, power indicator LED, status LED, and standard 4-pin header, turning a raw component into something that plugs directly into a breadboard.

SW1801P – How It Works

The onboard circuitry conditions the SW-520D’s brief mechanical contact closures into a cleaner digital signal, with the status LED lighting up visibly whenever a trigger event occurs, which makes bench debugging noticeably easier than watching a bare switch’s output on a multimeter alone. It draws a modest 0.3mA when actively triggering and drops to about 60μA on standby, running from a standard 3.3-5V supply that matches most Arduino and ESP32-family boards directly. An M3 mounting hole on the PCB also makes it straightforward to bolt the module rigidly to a project enclosure rather than leaving it loose on wires.

Key Features

  • SW-520D tilt switch pre-mounted with support circuitry
  • Power and trigger-status LEDs onboard
  • 4-pin header (VCC, GND, digital out, plus mounting)
  • M3 mounting hole for secure installation

Typical Applications

  • Breadboard-friendly tilt/shock detection prototyping
  • Tamper and impact alarm circuits
  • Educational projects introducing basic switch sensors

Specifications

  • Operating voltage: 3.3-5V DC
  • Current: ~0.3mA triggering, ~60μA standby
  • Interface: 4-pin digital output header

Specifications are sourced from HandsOn Tech’s SW520D tilt/vibration sensor module reference. Because this module already includes the support circuitry a bare SW-520D switch needs, it’s a faster starting point for beginners than wiring the raw switch with a separate pull-up resistor by hand from scratch.

Because the underlying switch is still mechanical and unidirectional, mounting orientation still matters even with the extra board circuitry, so test triggering in the actual installed position before finalizing a design.

Looking for more sensors? Browse our full range of sensors and modules.


موديول مفتاح اهتزاز SW1801P (4 بنات)

موديول مفتاح اهتزاز SW1801P بياخد مفتاح SW-520D الميكانيكي العاري وبيركبه على بورد مع دائرة مقارنة ومؤشر LED طاقة ومؤشر حالة وهيدر قياسي 4 بنات، وبيحول مكون خام لحاجة بتركب مباشرة على البريدبورد.

SW1801P – إزاي شغال

الدوائر المدمجة بتعالج توصيلات التلامس الميكانيكية القصيرة بتاعة SW-520D لإشارة رقمية أنضف، ومؤشر الحالة بينور بوضوح كل ما يحصل حدث تفعيل، وده بيخلي تصحيح الأخطاء على المنضدة أسهل بكتير من متابعة خرج مفتاح عاري بمقياس فقط. بيسحب 0.3 مللي أمبير متواضعة وقت التفعيل النشط وبينزل لحوالي 60 ميكرو أمبير في الاستعداد، وبيشتغل من تغذية قياسية 3.3-5 فولت بتطابق أغلب بوردات أردوينو وESP32 مباشرة. ثقب تركيب M3 على البورد كمان بيسهل ربط الموديول بإحكام لعلبة مشروع بدل ما يفضل سايب على أسلاك.

المواصفات الأساسية

  • مفتاح ميل SW-520D مركب مسبقًا مع دوائر دعم
  • مؤشرات LED للطاقة وحالة التفعيل مدمجة
  • هيدر 4 بنات (VCC، GND، خرج رقمي، تركيب)
  • ثقب تركيب M3 لتثبيت آمن

الاستخدامات

  • تجريب كشف ميل/صدمة مناسب للبريدبورد
  • دوائر إنذار تلاعب وصدمة
  • مشاريع تعليمية بتقدم حساسات مفتاح أساسية

المواصفات الفنية

  • جهد التشغيل: 3.3-5 فولت تيار مستمر
  • التيار: ~0.3 مللي أمبير تفعيل، ~60 ميكرو أمبير استعداد
  • الواجهة: هيدر خرج رقمي 4 بنات

المواصفات مأخوذة من مرجع HandsOn Tech لموديول SW520D للميل/الاهتزاز. وبما إن الموديول ده بالفعل شامل دوائر الدعم اللي مفتاح SW-520D العاري محتاجها، هو نقطة بداية أسرع للمبتدئين من توصيل المفتاح الخام بمقاومة سحب منفصلة بإيده.

محتاج حساسات تانية؟ تصفح باقي الحساسات والموديولات عندنا.

Shipping & Delivery
Reviews (0)
0 reviews
0
0
0
0
0

الآراء

Clear filters

لسه مفيش تقييمات.

كن أول من يقيم “SW1801P Vibration Switch Module 4 Pin”

بريدك الإلكتروني مش هيتنشر. الخانات المطلوبة معلّمة بـ *

لازم تكون مسجل دخول عشان تقدر تضيف صور لمراجعتك.